Battery Manufacturing EquipmentHangke cell-film wrapping equipment family
Hangke's cell wrapping machines apply insulating film around finished cells. The family handles several film-wrapping processes, controls film tension and binds each cell's data to MES. Hangke lists rates of ≥6/8/10/12 ppm across its configurations. Wrapping is the last step before cells go to module assembly.
Choose the film process first, then the rate
Hangke gives no supported cell sizes, film thickness or material, wrap path, tension range or overlap. Ask which cell and film combinations it has already run. Send your cell drawing, film specification, the coverage you need, any areas left bare and where seams may sit.
The ≥6/8/10/12 ppm options come without a list showing which process or cell each rate applies to, or how pieces are counted. Ask Hangke to quote the rate for your wrap once the wrapping moves and inspections are agreed. Ask also which tools and axes, preparation steps and handling are in the chosen option, and which film consumables it uses.
| Parameter | Published value | Record status |
|---|---|---|
| Listed rate configurations | ≥6 / ≥8 / ≥10 / ≥12 ppm | known |
Catalogue values apply to the configuration and test method the maker states. Ask for the values that apply to your configuration.
Source references: s1
Judging tension control by the finished wrap
Agree limits for wrinkles, lifting, tears, overlap and position on representative cells, paying attention to edges and corners that matter in your product. Ask for the tension setpoint and range, and how a roll change, splice or feed stop affects it. Hangke names tension control without giving its measuring or control performance.
Run your film and cells for a normal period, then a planned stop and restart or a film change. Inspect coverage and cell condition with the agreed sampling method. If you need an insulation test after wrapping, name the test station and the pass limit in the order, because the wrapping machine itself sets no test voltage.
MES binding, handover and line position
Specify what MES binding records: cell ID, wrapping recipe and configuration, film batch where needed, and inspection and rework status. Decide who releases cells and what happens when an ID cannot be read or an upload fails. Hangke does not publish the interface format, so define the database connection in the project.
At handover, get instructions for film loading, threading and tension setup, fixture changeover, wear parts and safe access to moving parts. Count good wrapped cells under the agreed reject and rework rules. Settle the configuration, film consumption and wrap quality through a trial with your own film.
Hangke's profile lists the end-of-line test equipment that checks cells before wrapping, and wrapping is the last step of the cell assembly sequence. The acceptance testing page explains how to check film placement on samples.
Wrapped cells are then grouped into modules, the step covered by the module and pack category.
Source references: s1
Questions that change the purchase
| Decision | What the catalogue says | Next step |
|---|---|---|
| Which rate corresponds to the proposed wrap? | The catalogue lists four rates without matching them to processes or cells. | Specify one installed configuration and how good output is counted. |
| What coverage is acceptable? | The catalogue sets no seam, wrinkle or bare-area limits. | Approve the film and cell drawing and inspect sample wraps. |
| Does MES binding include film/recipe changes? | The catalogue names data binding in general terms. | Define the record fields and who owns rework and release. |
Prepare the supplier conversation
Fill in the conditions below and ask the supplier to answer each open point in writing. Copying or downloading stays in your browser; nothing is sent.
Sources and check dates
The maker's own pages and public records used for this page, each with the date it was checked.
s1 · Hangke cell-film wrapping equipment family original public data
Hangke Technology · Manufacturer-origin source
Describes the wrapping processes, tension control, MES binding and rate options.
Archived source check: 2026-10-11
s2 · Hangke original post-processing equipment portfolio
Hangke Technology · Manufacturer-origin source
Shows the wrapping machines after Hangke's end-of-line test equipment.
Archived source check: 2026-10-11
Still to confirm
- The cell sizes, film types and tension range the machine handles.
- Which of the 6, 8, 10 or 12 ppm rates applies to your wrap, and how it is counted.
- Whether an insulation test station is included after wrapping.
- The MES binding fields and interface format.
Film wrapping of finished cells with tension control and MES binding
- Cell drawing, film material, thickness and coverage
- Seam and overlap, wrinkle, tear and position limits
- Tension range, threading and film-change trial
- Chosen rate configuration and good-output interval
- Insulation test after wrapping, if needed
- Film and recipe identity, rework, spares and MES recovery