Battery Manufacturing EquipmentGelon GN-S200P booster-cylinder electrode die cutter
Gelon's GN-S200P punches coated electrode sheets with an adjustable booster-cylinder press and pull-out tooling. It ships with standard positive and negative dies of 56 ×43 mm and 58 ×45 mm, cuts up to 180 ×150 mm and 0.5 mm thick with custom dies, and weighs 130 kg. It suits pouch and coin-cell labs, in a glovebox or on a bench.
By Gelon Lib Group Co., Ltd. · GN-S200P
Standard dies and the custom envelope
The standard positive die cuts 56 ×43 mm and the standard negative die 58 ×45 mm. With custom tooling the press cuts up to 180 ×150 mm including tabs, for aluminium or copper based electrodes up to 0.5 mm thick. Stroke is about 50 mm and the maximum punching entry reads 3 T; ask the supplier whether that means 3 tonnes of force.
Gelon describes pull-out tooling and a protective housing. One standard positive and negative tool set is included, and custom tools are made to your drawing. Die life is given as 5000–10000 operations without naming the material or wear limit. Input power is 100 W for the controls; the cylinder runs on external gas, so plan the gas supply separately.
| Parameter | Published value | Record status |
|---|---|---|
| Standard positive/negative die sizes | 56 ×43 / 58 ×45 mm | known |
| Maximum cut envelope including tabs | 180 ×150 mm | known |
| Maximum listed thickness | 0.5 mm | known |
| Approximate stroke | 50 mm | known |
| Published die-life reference; basis to confirm | 5000–10000 operations | known |
Catalogue values apply to the configuration and test method the maker states. Ask for the values that apply to your configuration.
Source references: s1
Set measurable edge limits
Send the collector, coating weight on each face, cut outline and tab area. Gelon describes minimal burr and no indentation but gives no burr height, size tolerance or delamination limit. Agree the measuring method and the limits your next process needs, and inspect first-off parts and later parts from the same die against them.
Ask how die clearance, registration and replacement are handled. Your electrode may need a new die before 10000 operations, so set the change point from measured edge and shape drift. Include waste removal and clean access to the pull-out tooling in the demonstration.
Source references: s1
Gas, glovebox space and transfer size
The cylinder needs 0.5–0.8 MPa of argon or nitrogen when the press sits in a glovebox, and plain compressed air on a bench. Order either the AC220 V/50 Hz or the 110 V/60 Hz build. The press measures about 662 ×582 ×830 mm and weighs 130 kg net. The packed length is listed as 600 mm, shorter than the body itself, so ask for a corrected packing and transfer drawing.
Check tool withdrawal, fixtures, support and access inside your own glovebox, which is a separate purchase. Under the supplier procedure, watch a die change, a deliberately mispositioned sheet and an interrupted stroke. Gelon gives no production rate, so measure accepted parts per hour with operator loading and inspection. Similar presses in the catalogue are useful for comparison when you need a different size or die.
Cut electrodes go on to stacking or coin-cell assembly, the winding and stacking category being the next step for pouch work.
Source references: s1
Questions that change the purchase
| Decision | What the catalogue says | Next step |
|---|---|---|
| Are both required dies in the quote? | The page lists standard 56 ×43 and 58 ×45 mm dies and a custom envelope up to 180 ×150 mm. | Approve positive and negative drawings and the delivered tooling. |
| When does edge quality require tool replacement? | The page gives 5000–10000 operations and describes minimal burr. | Agree material-specific wear samples and rejection limits. |
| Will it fit and remain serviceable in the glovebox? | The unit weighs 130 kg and the packed length is listed as 600 mm. | Get corrected transfer, support and tool-withdrawal drawings. |
Prepare the supplier conversation
Fill in the conditions below and ask the supplier to answer each open point in writing. Copying or downloading stays in your browser; nothing is sent.
Sources and check dates
The maker's own pages and public records used for this page, each with the date it was checked.
s1 · Gelon GN-S200P booster-cylinder electrode die cutter — manufacturer equipment page
Gelon · Manufacturer-origin source
Gelon's product page with standard die sizes, cut envelope, stroke, punching entry, die life, gas, power, size and mass.
Archived source check: 2026-10-11
s2 · Gelon official equipment portfolio
Gelon · Manufacturer-origin source
Gelon's equipment range, including other electrode cutters, notchers and stackers.
Archived source check: 2026-10-11
Still to confirm
- Burr height, cut size tolerance and delamination limit on your electrode.
- The material and wear limit behind the 5000–10000 operation die life.
- Gas flow per stroke and whether 3 T is the punching force.
- Corrected packed dimensions for moving the 130 kg press into a glovebox.
Pneumatic punching of positive and negative electrode sheets
- Collector/coating and positive/negative cut drawings
- Included 56 ×43/58 ×45 mm dies and custom tab envelope
- Force convention, stroke and tooling registration
- Burr, shape, delamination and tool-wear sampling
- Waste removal, die change and interrupted-cycle recovery
- Corrected transfer layout, support, gas flow and selected voltage