Battery Manufacturing EquipmentDZF-6050 laboratory vacuum drying oven
The TOB-DZF-6050 is a bench vacuum oven for drying battery materials, electrode sheets and cell cores in batches. It has a 415 × 345 × 370 mm stainless-steel chamber with two shelves and heats to 250°C. The vacuum pump is optional. It suits labs that dry small batches before assembly.
By Xiamen TOB New Energy Technology Co., Ltd. · TOB-DZF-6050
Chamber, temperature and power
TOB lists a 415 × 345 × 370 mm inner chamber in 304 stainless steel with two shelves. Temperature runs from room temperature plus 10°C up to 250°C, with ±0.5°C fluctuation at the controller. Temperature inside a loaded electrode stack can differ, so map it during your trial.
Power is 1,400 W on a choice of 110 or 220 VAC. The pump is optional and vacuum is given as −0.1 MPa. Ask whether that is a gauge reading, how it was measured, and which pump and vacuum fittings come with the oven.
| Parameter | Published value | Record status |
|---|---|---|
| Inner chamber | 415 × 345 × 370 mm | known |
| Temperature range | RT + 10 to 250 °C | known |
| Temperature fluctuation, catalogue | ±0.5 °C | known |
| Electrical power | 1400 W | known |
| Vacuum value as published | −0.1 MPa | known |
Catalogue values apply to the configuration and test method the maker states. Ask for the values that apply to your configuration.
Source references: s1
Plan the load first
An electrode sheet may lie flat in the chamber while its tray, spacers or a tall wound-cell fixture do not fit. Put the full loaded fixture dimensions in your enquiry. State how many shelves you will use and whether the load covers surfaces that need to transfer heat.
If your material gives off solvent, ask the supplier for the allowed load and the vacuum exhaust layout. Solvent recovery is not listed, so confirm which electrolyte or binder solvents the oven may handle.
Buying guidance from BatteryEquip.
Judge drying by the moisture result
Set the incoming material condition, the load size, the temperature and pressure log, and how moisture will be measured after drying. Record the time from opening the oven to protected transfer and measurement. An empty oven reaching its setpoint tells you little about a full batch reaching its moisture target.
Ask for a trial with your own tray layout and a full load. Keep the controller's fluctuation figure separate from a temperature map and from the moisture spread across the batch.
Dried electrodes then move to assembly, so the oven's unloading route should suit the cell assembly steps that follow.
Buying guidance from BatteryEquip.
Questions that change the purchase
| Decision | What the catalogue says | Next step |
|---|---|---|
| Will the full fixture fit? | The catalogue gives an inner chamber of 415 × 345 × 370 mm. | Send a tray drawing and get a loading layout with handling space. |
| What does −0.1 MPa mean in use? | The catalogue lists −0.1 MPa with no loaded pump-down curve. | Agree pressure reference, pump, leak test and a loaded drying log. |
| How will drying be accepted? | The catalogue gives ±0.5°C controller fluctuation and no moisture data. | Set a moisture method, sample positions and protected transfer for the trial. |
Equipment questions
Is the vacuum pump included?
TOB lists the pump as optional. Ask for an itemised list of pump, hose, valve and exhaust, so you can see the full drying setup alongside the oven price.
Source s1Prepare the supplier conversation
Fill in the conditions below and ask the supplier to answer each open point in writing. Copying or downloading stays in your browser; nothing is sent.
Sources and check dates
The maker's own pages and public records used for this page, each with the date it was checked.
s1 · DZF-6050 laboratory vacuum drying oven — original equipment page
TOB · Manufacturer-origin source
TOB's product page for the DZF-6050, with chamber size, shelves, temperature range, vacuum figure and power.
Archived source check: 2026-10-11
s2 · TOB equipment catalogue
TOB · Manufacturer-origin source
TOB's equipment catalogue, listing this oven with its other drying equipment.
Archived source check: 2026-10-11
Still to confirm
- The pump model and fittings included in your quotation.
- Temperature spread inside a loaded batch.
- Residual moisture on your electrodes or cell cores after drying.
- Which solvents the oven may handle and the exhaust needed.
Batch vacuum drying of electrodes and cell cores
- Material and allowed temperature
- Tray and full loaded-fixture dimensions
- Batch load and shelf layout
- Pump, exhaust and solvent handling
- Residual-moisture target and test method