Battery Manufacturing EquipmentKejing organic-solvent laboratory spray dryer
The Kejing MSK-DZF-15-0S is a lab spray dryer for liquid feeds that contain organic solvent. It atomises the feed into circulating nitrogen and condenses the solvent in two stages. Feed rate is 50–2000 mL/h through a 0.7 mm two-fluid nozzle. It suits labs making small powder batches for battery materials.
By Shenzhen Kejing Star Technology Company · MSK-DZF-15-0S
Feed rate, nozzles and temperatures
Kejing lists a liquid feed of 50–2000 mL/h and a standard 0.7 mm two-fluid nozzle, with 0.5 and 1.5 mm nozzles as options. How much dry powder you get depends on the solids in the feed and on recovery. Kejing gives a drying time of 0.8–1.5 s with no material attached, so check particle dryness on your own feed.
The recommended inlet range is 30–250°C with ±0.5°C control. A 300°C upper figure also appears, but Kejing warns that running there damages the seals. Outlet temperature is listed at 30–100°C. Start a new solvent or formulation well inside these limits and raise temperature only after a trial.
| Parameter | Published value | Record status |
|---|---|---|
| Listed liquid-feed range | 50–2000 mL/h | known |
| Standard nozzle diameter | 0.7 mm | known |
| Recommended inlet-temperature range | 30–250 °C | known |
Catalogue values apply to the configuration and test method the maker states. Ask for the values that apply to your configuration.
Agree the solvent operating range with Kejing
Nitrogen flow runs 0–25 L/min, with 15 L/min recommended. Kejing describes two-stage condensation and cooling, and a feed interlock that trips when oxygen rises above an adjustable threshold, set below 3%. That setting is Kejing's default, so ask what threshold suits your solvent. Ask too for the safety certification that applies to the pressure-relief design in your country.
Send the solvent name, concentration, feed properties and expected vapour load. Ask the manufacturer to write down the approved operating conditions, oxygen measurement and interlock, condenser and cooling duty, exhaust and recovery setup and installation needs for that solvent. Nitrogen generation and remote operation are optional, so list them if you want them.
Track powder in the collector and through the system
Run a representative feed and agree which powder properties matter for your work: residual moisture or solvent, size distribution, agglomeration and usable recovery. Weigh powder left in the cyclone, chamber and filters as well as the amount collected. Kejing gives no recovery percentage for any recipe and no battery-material results.
Record feed and nozzle settings, measured temperatures and a mass balance with each accepted sample. Check cleaning and carryover after switching to a different composition, and set a maintenance plan for nozzle, filter and condenser. A good spray run is the first step; the powder still needs its own acceptance in the electrode process after drying.
Spray-dried powders are later mixed into slurry, the step covered by the slurry mixing category, and the acceptance testing page sets out a way to agree particle and moisture checks on the product. Kejing's dual-planetary mixers are the usual next step.
Questions that change the purchase
| Decision | What the catalogue says | Next step |
|---|---|---|
| How much usable powder is recovered? | The catalogue gives liquid feed of 50–2000 mL/h. | Agree a solids balance and recovered-powder criteria. |
| Is your solvent approved? | The catalogue lists an oxygen interlock with an adjustable threshold below 3%. | Get a written operating and installation scope for your solvent. |
| Are optional items included? | The catalogue lists extra nozzles, nitrogen generation and remote operation as options. | List the delivered system and who services each part. |
Prepare the supplier conversation
Fill in the conditions below and ask the supplier to answer each open point in writing. Copying or downloading stays in your browser; nothing is sent.
Sources and check dates
The maker's own pages and public records used for this page, each with the date it was checked.
s1 · Kejing organic-solvent laboratory spray dryer original specification
Shenzhen Kejing · Manufacturer-origin source
Kejing's specification for the MSK-DZF-15-0S, with feed rate, nozzles, temperatures, nitrogen flow, condensation and interlocks.
Archived source check: 2026-10-11
s2 · Official current equipment catalogue
Shenzhen Kejing · Manufacturer-origin source
Kejing's current catalogue listing its drying and powder preparation equipment.
Archived source check: 2026-10-11
Still to confirm
- Approved operating conditions and oxygen threshold for your solvent.
- Powder recovery and residual solvent on your feed.
- Safety certification for the pressure-relief design at your site.
- Which nozzles, nitrogen generation and remote options are included.
Lab spray drying of solvent-based feeds in nitrogen
- Solvent name, concentration and feed solids and rheology
- Nozzle choice, feed rate and powder target
- Approved oxygen, temperature and pressure range
- Cooling, condensation, nitrogen and exhaust connections
- Recovery balance, residual solvent and powder sampling
- Cleaning, filters, nozzle wear and optional items