Battery Manufacturing EquipmentAutomatic Electrode Slurry Mixing System
Gelon offers an automatic mixing system for the preprocessing end of an electrode line, preparing and dispersing cathode and anode slurry with nanoscale additives such as conductive carbon and carbon nanotubes. The catalogue lists site conditions of 20–30 °C and humidity at or below 30%, but no vessel volume, so the batch size comes from a model-specific proposal.
What the catalogue describes
Gelon places this system in production-line preprocessing. It covers cathode and anode slurry preparation and dispersion of nanoscale materials, including conductive carbon and carbon nanotubes. The page describes good efficiency and dispersion in general terms and gives no numerical trial figures.
The published index lists a working temperature of 20–30 °C, relative humidity no greater than 30%, the electrical supply and dry compressed air at 0.5–0.7 MPa. These are conditions for the room and utilities. They tell you how to prepare the site, and they say nothing about slurry temperature, mixing capacity or dispersion quality.
Batch volume, mixer type, cycle time and slurry output are not given. Ask for a model-specific proposal covering the vessel working charge, how materials are added, the vacuum or dispersion arrangement, cleaning and transfer. Production capacity should be calculated from that proposal.
| Parameter | Published value | Record status |
|---|---|---|
| Dry compressed-air supply | 0.5..0.7 MPa | known |
| Installation relative humidity | ≤30% | known |
| Installation working temperature | 20..30 °C | known |
Catalogue values apply to the configuration and test method the maker states. Ask for the values that apply to your configuration.
Source references: s2
Define when slurry is ready for coating
Give Gelon your solids content, solvent and the condition of incoming powders, then name the property that releases a batch to coating. Agree the sampling points and how much material stays in the system after discharge. This matters most when conductive additives are pre-dispersed before the final mix.
The proposal should split storage, dosing, mixing, filtration and transfer, and mark which items you already own and which Gelon supplies. Ask for a recorded trial on the route you choose, run with your formulation.
Buying guidance from BatteryEquip.
Points to settle with Gelon
A 2022 study lists GELON LIB Group as a source of electrolyte and pouch-cell materials, which shows the group supplies materials to laboratories. It says nothing about this mixing system, and the group has more than one company. Before ordering, ask which company will sign the contract, and request batch capacity, the process layout, current safety documents and the acceptance measurements.
Buying guidance from BatteryEquip.
Agree the slurry endpoint before choosing a package
Open the enquiry with your formulation, the batch size you really need, the addition sequence and the measurements you will use to accept slurry. Ask the proposal to state vessel working charge, the mixing and dispersion arrangement, the discharge method and expected transfer losses. With those figures you can size the plant without guessing litres per batch.
Request a trial on the offered system that records inputs, settings, sampling method and the measured outgoing slurry. Include cleaning and a changeover to your next formulation where carryover matters. Keep the room conditions in the index apart from the slurry temperature your process needs.
Questions that change the purchase
| Decision | What the catalogue says | Next step |
|---|---|---|
| Which mixer and batch size are quoted? | The catalogue gives no mixer volume. | Request vessel drawings, effective fill and usable batch output. |
| How is slurry quality maintained through transfer? | The catalogue describes the route but lists no process settings. | Specify viscosity, temperature, transfer loss and sampling points with the supplier. |
Equipment questions
Is 20–30 °C the slurry-processing temperature?
No. The index lists it next to room humidity and utilities, so it describes the site. Ask Gelon for the actual process temperature for your formulation.
Source s2What output can I use in a factory capacity calculation?
The catalogue gives no batch or output number. Use the figure in a configuration-specific proposal, backed by an agreed trial or acceptance test.
Source s2Prepare the supplier conversation
Fill in the conditions below and ask the supplier to answer each open point in writing. Copying or downloading stays in your browser; nothing is sent.
Sources and check dates
The maker's own pages and public records used for this page, each with the date it was checked.
s1 · Company and supply-scope record
Gelon Lib Group Co., Ltd. · Manufacturer-origin source
Gelon's own company information and the range of equipment and materials it says it supplies.
Archived source check: 2026-10-07
s2 · Automatic Electrode Slurry Mixing System
Gelon Lib Group Co., Ltd. · Manufacturer-origin source
Gelon's catalogue entry for this system, with the process description and the site temperature, humidity and air supply.
Archived source check: 2026-10-07
s3 · Official portfolio context
Gelon Lib Group Co., Ltd. · Manufacturer-origin source
Gelon's wider product range, showing the mixers and line equipment that could sit around this system.
Archived source check: 2026-10-07
s4 · 2022 autonomous electrolyte study: Gelon materials availability
Europe PMC / EMBL-EBI; Nature Communications · Public original record
A published study whose materials list names GELON LIB Group as a source of electrolyte and pouch-cell materials; the study's authors built their own robot.
Archived source check: 2026-10-11
Read original record →Still to confirm
- Which Gelon group company signs the contract and who makes each item in the package.
- The vessel working charge, usable batch output and slurry output per shift.
- Transfer losses and the cleaning procedure between formulations.
- The slurry process temperature and viscosity window for your recipe.
Automatic cathode and anode slurry preparation for production lines
- Formulation and solids range
- Effective batch output
- Temperature and viscosity criteria
- Transfer, filtration and cleaning boundaries